...
| TypicalHeader | Lead Question | Content expected |
|---|---|---|
| Introduction | What is the challenge? | Describe the engineering challenge cleary derived from a need, e.g. of society, of other engineering challenges, of prior work |
| Scientific question / Target | What is the base-hypotheses of your work - the scientific question? | Based on the challenge you usually define a scientific question your work follows. Weak questions are something like "to generally improve control" or "to find a solution for", strong questions are "to improve control to lower than 5% control error" or "to find a solution reaching the bandwith from 100 Hz at 5 N amplitude". In other words, the scientific question is usually quantified. Not necessarily in the same sentence, but this is the "requirements"-section based on which you will later evaluate the performance of the solution |
| Prior Work / Prior Art / Earlier Achievements | What is prior work, how did others solve it? | There is always prior work. It may not be precisely your question, but it always is related. In this part the top 10 related topics are cited. Make sure to catch the most important ones. Good guidelines are always to check for the number of citations of the source you choose and try to find the "top-cited-author" in the area of your research. Usually you are searching for two extrems, the eldest fundamental paper most people refer to, and the newest publications who cite the top-cited author. |
| The Design / Engineering Design / The Device / Experimental setup | Your solution, the fun part | In this part you are describing your solution. As we usually are discussing multi-domain-topics in mechatronics, this part frequently consists of a mechanic, a control and sometimes an electronic component. Try to avoid trivial topics. There is NO VALUE in Arduino or Rasperry circuits. Although this may be something you found extremly interesting and a big learning for yourself, believe me, it is not for engineers in general and especially not for the reviewers you are going to face in a peer-review. You should mention the components you used as precisely as possible, but stick to unusual things, not to things you can find with 1h search in the internet! |
| Verification experiment / Tests & Experiments / User-Study and Tests | Verification according to hypothesis | The next step is to verify your design according to the initial hypothesis. Make sure to focus on answering the questions and requirements from your hypothesis, but on top of that extend your findings by some additional discussions. Show data, show them in a physical base (time, frequency, m/s2), do not show based on "samples taken" or "discretization". People need to compare their findings with yours, do not hide your findings by units no one can use. For verification, you should have spent equally as much time as for the design itself. The experiments must be chosen carefully, the material must be prepared in high quality and the measurements must be beyond any doubt. You may not be able to answer everything, so it is okay if some unexpected effects/findings occur. Be honest and clear on them. So if you did not plan your verification and your experiments are done last-minute, do not publish! In HMIs verification there is a frequent need to involve several people and do some psychophysiological experiments. If you do this, make sure that you are following the concept of psychophysical studies and argue in the standards (JND, DL, Confusion-Matrix, ...) which are typical to this domain. Do not just say: "People liked it", no one will believe you! |
| Outlook / Next Steps / Succeeding topics / Discussion | Outlook | There is an expectation that you create/discuss two directions in your outlook. One part must be data-driven and is more or less a "next-steps" kind of thing based on the data availabe from your experiments. The other part can be highly speculative. Ideally it combines your research with the prior-art research and formulates a next hypothesis which you suggest as a next step for your work, or you suggest it as a next step for the community. |
| Final sentence | Do not forget to mention grants, if you had some which were financing you. | |
| Abstract | Abstract | The abstract is of course the first part of the publication. But honestly, the abstract is written at the very end. It is like a short-version of the paper. It must be conclusive, touch all topics above (one sentence per topic). |
Beside this content-focussed article, there are other resources in the net who focus more on the style of writing. I am quite convinced that anyone has his/her own style to structure time and content for writing an article. However if you need some inspiration, I recommend e.g. this as one idea: https://spie.org/news/photonics-focus/janfeb-2020/how-to-write-a-scientific-paper?SSO=1